Showing results: 1261 - 1275 of 1660 items found.
-
SUG335 -
Lisun Electronics Inc.
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
NOVOTEST IPSM-U+T+D (Pulse Velocity Tester) -
NovoTest
The pulse velocity tester IPSM-U+T+D allows to measure the strength and homogeneity of the concrete, bricks and other materials under the composition and surface sounding in products and designs for construction projects, inspection of buildings and structures, according to ASTM C597-16 (Standard Test Method for Pulse Velocity Through Concrete). Has the determining of the depth of cracks by the surface sounding probe function and also flaw detection mode (A-scan).
-
CZ20054 -
Aegis Pty. Ltd.
Australian and New Zealand standards mandate testing of fault loop impedance on circuits not protected by RCD's, both at installation and after maintenance. The CZ20054 Loop Impedance Tester conducts earth fault loop impedance and prospective short circuit current (PSC) tests. The Aegis Loop Impedance Tester takes the confusion out of loop/psc testing by providing an automatic wiring check upon connection and single button operation.
-
RT600 -
Klein Tools, Inc.
Designed to detect the most common wiring problems in standard 120V receptacles.Also tests GFCI receptacles for proper operation.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.
-
N5264B -
Keysight Technologies
A new industry standard for antenna test with 400,000 point per second data acquisition on all five measurement channels Twice as many receivers available compared to any other antenna receiver on the market Replace existing 8530A and 8360 solutions for a system speed improvement that is 10 times faster Built-in 8510/8530A code emulation software provides a drop-in replacement for existing antenna ranges utilizing an 8530A
-
M9132A -
Keysight Technologies
The M9132A is a high-density, general purpose switch with50 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100Vrms and 1A, with up to 25W power. Choose from the durable connector block or standard cable connections.
-
M9133A -
Keysight Technologies
The M9133A is a high-density, general purpose switch with 100 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100Vrms and 1A, with up to 25W power. Choose from the durable connector block or the standard cable connections.
-
X-COM Systems
Our Components product line consists of standard RF components and unique designs for custom microwave applications. We provide rugged, reliable and quality solutions for low and high power attenuation, termination, coupler, and power-divider applications. In addition to our extensive line of standard products, Bird has a reputation for designing custom solutions for custom applications. Bird has done hundreds of special versions of RF components to meet the unique needs of our customers. Common requests for customization include: Special Connectors, Non-Standard Attenuation Values, Mismatch Loads, Exceptional Peak or Average Power Handling Capability, Extremely Low VSWR Requirements, Custom Test Requirements and many others!
-
Instron
These three zone resistance wire wound furnaces are of split construction to facilitate fast and easy loading of a pre-assembled specimen train. The case is constructed from stainless steel with aluminium and hardened insulation board end plates. The optional front cut-out allows the use of side-entry high-temperature extensometry. Adjustable stainless steel latches keep the furnace halves locked together during use, but are then easily opened once testing is complete. The furnace is available with optional heavy duty brackets or mountings, which attach to a wide range of testing systems. An extensive range of standard controllers is available to suit most test regimes. Custom variants can be specified should the standard range not include a suitable unit.
-
Meco Instruments Pvt. Ltd.,
Max. solar system power (Pmax) search by Auto-scan: 1000V, 12A (12000W capability)The analyzer and the Remote Solar Detector is connected by Bluetooth wireless communication (Bluetooth 2.1 + EDR Class 1)The Remote Solar Detector is moisture-proofIntelligent test logic with no personnel attendance required in the field Solar system analyzer waits and tests the system until appropriate sunlight irradiance is detectedMax. voltage (Vpm) at Pmax, Max. current (Ipm) at Pmax Voltage at open circuit (Voc), Current at short circuit (Isc)Efficiency (%) calculation of solar systemTemperature measurement of solar panelsIrradiance measurement of sun lightSeries resistance (Rs) calculation of solar panelsWith data logging/open function, the I-V curves of solar system can be analysed / recorded for a period of time (e.g. 60 min.)Conversion of I-V curve under OPC to data under standard test condition (STC) based upon IEC standardProvide Operating Condition (OPC) and Standard Test Condition (STC) test reports for verification of solar panel performance (OK or NO OK)Users can set up the parameters of solar panelsUsers can set up the series number of solar panels. Parameters of many solar panels can be measured in one measurementThe Irradiances and Temperatures of solar panels can be continuously measured, monitored and recordedContinuously measure/monitor/record the DC power output of solar system and the AC power output of inverter (1 phase or balanced 3 phases)Calculate the efficiency of DC to AC power conversion and the efficiency of the max.output power
-
TUV Rheinland Inc
Unmanned aerial vehicles (UAVs), more commonly known as drones, have many applications. UAVs can be used in agriculture for crop spraying, movie making and aerial photography, disaster relief, and can even imitate flying animals for conservation or research purposes. Our services can help you make sure your UAVs meet international norms and standards. We test materials and resilience, confirming that your drones do not pose a threat to human health or the environment. Our services can help you make sure your UAVs meet international norms and standards. We test materials and resilience, confirming that your drones do not pose a threat to human health or the environment. Our team of experts is dedicated to UAVs and their applications – and a global network of offices. We can give you the advice and expertise you need to speed your drones to market. Our team of experts is dedicated to UAVs and their applications – and a global network of offices. We can give you the advice and expertise you need to speed your drones to market.
-
LBA Group, Inc
LBA's EMFaraCage® faraday cages are EMI and RFI shielding boxes and RF test enclosures that bring convenience to device testing. Faraday cages are ideal for isolating critical systems in high field RF environments or wherever RF ingress or egress must be minimized. Security, production testing, biomedical research and semiconductor testing are only a few of the many areas where EMFaraCage® faraday shielded enclosures are employed. EMFaraCage® faraday cage enclosure systems are fully featured to support a wide variety of test missions. The standard faraday cages include effective power, dataline and RF signal isolation in large test volumes. EMFaraCage® faraday cages are much more affordable than shielded room solutions and offer the convenience of portability.
-
STG-06-S1 -
ERAVANT
Full band noise figure and gain test extenders are offered to extend noise and gain measuring capabilities up to higher millimeterwave frequency ranges. These extenders are designed to interface with noise and gain test systems that have an input IF of 10 MHz to 1.6 GHz, such as the industry standard Keysight 8970A/B, N8975A and Maury MT 2075B. The noise figure and gain test extenders include a high-performance, solid-state noise source (STZ series) and a full waveguide down converter (STC series), which consists of a Faraday isolator (STF series), full band mixer (SFB series), frequency multiplier, and IF amplifier. A frequency source with an output signal in the frequency range of 10 to 20 GHz is required as a local oscillator for the down converter. The noise source is automatically powered on and off by the noise figure meter.
-
CodeReport -
Test Spectrum, Inc.
CodeReport is an easy-to-use application for verifying test program quality. CodeReport comes with many different, known quality screening rules that can be used to verify your test program is complete and ready for production. CodeReport also provides a graphical Rule Editor that allows you to create your own, custom rules. Ensure your coding standards and quality specifications are correct by generating your set of rules, checks, and screenings. Easily generate a detailed report for locating, correcting, and documenting the state of your test program. Quickly identify the tester hardware and instrumentation needed to run your program with the Tester Resource report. Save a session file to quickly return to your project after edits have been made or use the Session on other similar projects to transfer your configuration and custom rules.
-
MR-30 -
PINTEK Electronics
*Double LCD Display*300,000 counts resolution*Measurement Range: 30mΩ~3MΩ*0.05% accuracy*20 Standard User setting memory sets*Sorting function and Relative percentage function*PASS/FAIL test result alarm*Computer Remote Manual and Auto Scan function*Manual and Auto Channel select*Sampling Rate: 30 sample/sec*High Resolution Temperature compensation and measurement*DUT Four-wire method*USB interface
